Installing factory rear vision camera on 2014

Electronic systems, stereo and Holden iQ, wiring, it all goes here....
smokin14ppv
Posts: 2
Joined: Tue Dec 10, 2019 2:57 am

Re: Installing factory rear vision camera on 2014

Post by smokin14ppv » Tue Dec 10, 2019 4:05 am

smwalker wrote:
Fri Nov 15, 2019 3:26 pm
Can build in a day. Have all the stuff for like 3 of them.
any supplies to build another? interested

smwalker
Posts: 1903
Joined: Mon Jul 29, 2013 6:44 am
Location: Azusa,CA

Re: Installing factory rear vision camera on 2014

Post by smwalker » Sat Dec 14, 2019 3:49 am

smokin14ppv wrote:
Tue Dec 10, 2019 4:05 am
smwalker wrote:
Fri Nov 15, 2019 3:26 pm
Can build in a day. Have all the stuff for like 3 of them.
any supplies to build another? interested
I have stocked up and ready to make them up. Cost is $75.00 - Paypal (Friends and family) or Zelle to PPVSteve@Gmail.com - Let me know your shipping address and what year you are installing into. 14+ get the terminals for the X4 radio plug. 11-13 get an RCA male end.
Steve Walker
Azusa, CA
'11 PPV 9C3 Huron White

WildGS
Posts: 14
Joined: Wed Feb 27, 2019 6:23 am

Re: Installing factory rear vision camera on 2014

Post by WildGS » Sat Dec 14, 2019 6:23 am

Just installed a WN camera in my 2012. Easy once the radio is programmed and an RCA jack installed. OEM camera clips into stock chrome trim. You will lose your trunk key unless you relocate. Used Steve's harness, still have to route through the car but seems to work. All plug and play except one splice to the backup light.
20191210_212716.jpg
20191210_212716.jpg (3.16 MiB) Viewed 1662 times
20191213_194732.jpg
20191213_194732.jpg (2.7 MiB) Viewed 1662 times
20191213_162540.jpg
20191213_162540.jpg (2.99 MiB) Viewed 1662 times
20191213_161501.jpg
20191213_161501.jpg (3.42 MiB) Viewed 1662 times
Attachments
20191213_194247.jpg
20191213_194247.jpg (2.58 MiB) Viewed 1662 times

Godssondp
Posts: 4
Joined: Fri Jun 28, 2019 8:34 pm
Contact:

Re: Installing factory rear vision camera on 2014

Post by Godssondp » Mon Feb 24, 2020 9:11 pm

Very Great write-up. Curious about differences in the deck lids between the years 2011 and 2015. Between my friend and I, we own a 2011,2012 and a 2013. Could we use the factory 2015 camera and trim on any of these or can we make it work? Looks like we just need to cut the square hole for the camera and drill the 2 mounting holes on each side. Thanks in advance for any info.
David
2013 Caprice 9C1 Black cherry paint, Iron 6.0, LS3 cam, mufflers, Dod delete, Corvette rims (acquired in July 2019)
2012 Caprice 9C1 White Metallic paint, Iron 6.0, LS3 cam, headers, Dod delete, G8 rims (acquired in June 2019)
2005 Silverado SWB 6.0, sq port #823 ported, .600 lift, 3200 Yank, 4L80e (traded for 2012 PPV)
1979 Mercury Capri 410W stroker, Edelbrock RPM heads & Intake, Rollin Thunder cam, 5-speed, 3.73

Pursuit
Administration Staff
Posts: 766
Joined: Tue Apr 23, 2013 8:39 pm
Location: Omaha, NE area

Re: Installing factory rear vision camera on 2014

Post by Pursuit » Tue Feb 25, 2020 5:39 am

You just remove the key lock assembly from the trim garnish and install the camera there. The lock assembly is dimensionally the same as the camera. You will need to remove the trim garnish across the back of the trunk. I did buy a 2015 trim garnish to use with the camera. Not for sure but the original trim garnish may work. Keep in mind that you will lose the ability to unlock the trunk manually. I already had a fold down center section where I could pull the emergency trunk release.

Maurice
Maurice Sheil

mhsheil@gmail.com

2011 Caprice Phantom Black 9C3
2012 Impala 9C1
1995 9C1 Caprice
1996 GMC Sierra C1500
1974 SJ Grand Prix 455 well optioned with factory moon roof

WildGS
Posts: 14
Joined: Wed Feb 27, 2019 6:23 am

Re: Installing factory rear vision camera on 2014

Post by WildGS » Tue Feb 25, 2020 7:13 am

camera should pop in any factory trim, no modifications needed

smwalker
Posts: 1903
Joined: Mon Jul 29, 2013 6:44 am
Location: Azusa,CA

Re: Installing factory rear vision camera on 2014

Post by smwalker » Mon Mar 09, 2020 11:44 pm

Update to a part number for this project - Maybe. Someone looking for the camera at various sites today noticed one site said the camera part number had been replaced by 92288994 - None of the sites had any vehicle fitment information but then again they did not have much for the original part number for the camera. I looked around and found the part number to be used on the 11-13 middle east caprices. Now why a part number from 11-13 would replace a part number for a 2015 model part is beyond me. Still need to find out if the harness that connects to it is the same and if the connector and wires are all the same . Only reason I mention it now is it's $100 less so if you are on the cusp of buying may want to wait till we find out whats up.

Will update with findings.
Screenshot 2020-03-09 at 3.35.37 PM.png
Middle East Caprice Camera Listing
Screenshot 2020-03-09 at 3.35.37 PM.png (597.65 KiB) Viewed 1287 times
Steve Walker
Azusa, CA
'11 PPV 9C3 Huron White

smwalker
Posts: 1903
Joined: Mon Jul 29, 2013 6:44 am
Location: Azusa,CA

Re: Installing factory rear vision camera on 2014

Post by smwalker » Tue Aug 11, 2020 6:45 am

Just a FYI and a heads up - Got this from another member:

I received the cameras, I ordered from GM out of TX the better 2247 camera for $119 and received the 8994. kinda pisses me off because another dealer had the 8994 for $91. So Ill let you know how it goes. It must be an automatic replacement part #.

Looks like GM playing fast and loose with part numbers!
Steve Walker
Azusa, CA
'11 PPV 9C3 Huron White

s/c'd cav
Posts: 935
Joined: Mon May 30, 2016 8:12 am
Location: PHOENIX AZ

Re: Installing factory rear vision camera on 2014

Post by s/c'd cav » Tue Aug 11, 2020 4:20 pm

the GM parts catalog used to show 2 different part #'s , now it only lists the one # 92292247

smwalker
Posts: 1903
Joined: Mon Jul 29, 2013 6:44 am
Location: Azusa,CA

Re: Installing factory rear vision camera on 2014

Post by smwalker » Sun Aug 16, 2020 10:35 pm

s/c'd cav wrote:
Tue Aug 11, 2020 4:20 pm
the GM parts catalog used to show 2 different part #'s , now it only lists the one # 92292247
Could you also check 92288951 the lid harness, just got word that might be discontinued. See any stock anywhere? I need to get my hands on one to copy if discontinued.

Of if anyone has one that you have not installed yet break out the camera and tape measure!!
Steve Walker
Azusa, CA
'11 PPV 9C3 Huron White

Post Reply