Search found 25 matches
- Fri Sep 29, 2023 8:43 am
- Forum: Drivetrain tech
- Topic: 2013 Driveshaft u-joint part number?
- Replies: 9
- Views: 954
Re: 2013 Driveshaft u-joint part number?
Interesting, just have to figure out the size and type. There are lots of u joints out there. The Spicer and Neapco are my go to, for my 4X4 stuff. I have not removed the ujoint in fear of not having something to put back in as it is not trashed, I just wanna go thru the drive line since it is out a...
- Thu Sep 28, 2023 9:02 am
- Forum: Drivetrain tech
- Topic: 2013 Driveshaft u-joint part number?
- Replies: 9
- Views: 954
Re: 2013 Driveshaft u-joint part number?
Could be, u never know where these cars have been. I have seen rebuilt shafts with clips advertised. So the mystery contiues...
- Wed Sep 27, 2023 8:52 am
- Forum: Drivetrain tech
- Topic: 2013 Driveshaft u-joint part number?
- Replies: 9
- Views: 954
Re: 2013 Driveshaft u-joint part number?
Mine has cir clips, so I figured it was replaceable. Driveshaft shop is a good idea for their input. Driveshaft assy's are over $700 for GM. THX
- Tue Sep 26, 2023 2:23 pm
- Forum: Drivetrain tech
- Topic: 2013 Driveshaft u-joint part number?
- Replies: 9
- Views: 954
2013 Driveshaft u-joint part number?
I was wanting to overhaul my drive shaft while out of the car, found carrier bearing and boot kit for mid shaft. I can not find anywhere a P/N for the u-joint that goes aft of the carrier bearing. GM does not list one, nor AC Delco. No parts houses show one either. Anybody run into this and what did...
- Tue Aug 31, 2021 8:53 am
- Forum: Stereo / Electronics / Electrical
- Topic: 2013 Chevy Caprice Steering Wheel info Button
- Replies: 3
- Views: 3179
Re: 2013 Chevy Caprice Steering Wheel info Button
Turns out someone programed my DIC to off with a Tech 2, probably a past dealer/ broker it went thru before I bought it. This way a buyer can't see engine idle hours easily. Had Dealer turn it back on.... I thought something was odd as the past owner had changed all the steering wheel switches to no...
- Wed Aug 18, 2021 12:43 pm
- Forum: Caprice PPV Parts for sale
- Topic: Parting out 2013 PPV 9C1
- Replies: 39
- Views: 33644
Re: Parting out 2013 PPV 9C1
Need a factory antenna (not the base) and a lower rear door scuff plate that is stuck on the sill trim. Victim is a '13 PPV. Antenna is particular to the 13, 14 up wont work. THX let me know.
- Thu Jun 24, 2021 9:28 am
- Forum: Suspension / Brakes / Steering
- Topic: Anybody running Pedders suspension?
- Replies: 5
- Views: 4531
Re: Anybody running Pedders suspension?
Thanks again, Great info, you answered my curiosity about using the Pedders setup. I have looked at about 5 other brands but like you say, this you can dial in ride height and adjust dampening. Other systems may lack one or the other, and then there is the mix and match strut/ spring combos that cos...
- Wed Jun 23, 2021 12:07 pm
- Forum: Suspension / Brakes / Steering
- Topic: Anybody running Pedders suspension?
- Replies: 5
- Views: 4531
Re: Anybody running Pedders suspension?
THX Capeasy, was it worth the $, maybe I should just put some slight lower springs on the stock struts....
- Fri May 28, 2021 8:50 am
- Forum: V8 engine tech (L77)
- Topic: Daily Driven Cam Choice
- Replies: 18
- Views: 14291
Re: Daily Driven Cam Choice
Ohh I did order the trunnion upgrade as well. I looked at ls3 and ls9 cams but they were not quite right for me although a good choice. Its all about what you need and how you are going to use it, like if you you plan on trailering. Just have have to stop, think and plan out whats best, then pull th...
- Thu May 27, 2021 12:21 pm
- Forum: V8 engine tech (L77)
- Topic: Daily Driven Cam Choice
- Replies: 18
- Views: 14291
Re: Daily Driven Cam Choice
Funny ... saw this after I order my cam this morning. This cam is 2 baby steps up from stock. Wanted a daily driver cam and not kill driveability or mileage. This does not need a stall conv and can be tuned to tweek it in. I have solo free flow cats, stock mid system and solo axle back exhaust. I wi...