CTSV2 wheels?
-
- Posts: 15
- Joined: Thu Dec 03, 2015 9:44 am
CTSV2 wheels?
i have the original set from my 09 V. i'd rather ave the cash but if they don't sell maybe i'll put them on the PPV. does anyone know if it they fit (pattern/spacing/etc)?
regards,
alex
vectorbundle[AT]gmail[DOT]com
2009 gray CTSV modded 700rwhp
2012 black 9C1 caprice PPV 3.45 diff
- eagle-co94
- Posts: 306
- Joined: Fri Oct 04, 2013 4:47 pm
- Location: Bloomington, Indiana
Re: CTSV2 wheels?
As far as I know they fit just fine.
-James . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . "Life without knowledge is death in disguise."
-
- Posts: 15
- Joined: Thu Dec 03, 2015 9:44 am
Re: CTSV2 wheels?
rears with 285s didn't fit, flush against wheel well on the inside.
regards,
alex
vectorbundle[AT]gmail[DOT]com
2009 gray CTSV modded 700rwhp
2012 black 9C1 caprice PPV 3.45 diff
-
- Administration Staff
- Posts: 1724
- Joined: Tue Mar 19, 2013 6:30 pm
- Location: Canton GA
Re: CTSV2 wheels?
a proper spacer setup could fix that, I'd think....
http://www.hrsprings.com/products/trak/" onclick="window.open(this.href);return false;
http://www.hrsprings.com/application/se ... /1516/2013" onclick="window.open(this.href);return false;
20, 22, 25, 30 mm spacer/adapter (Camaro application)
H&R does make thinner spacers http://www.trakplus.com/" onclick="window.open(this.href);return false; - similar to those below (from Motorsport Tech), but not for the GM Zeta wheel hub ID/OD
custom spacers:
http://www.motorsport-tech.com/wheel_spacers.html" onclick="window.open(this.href);return false;
http://www.motorsport-tech.com/wheel_adapters.html" onclick="window.open(this.href);return false;
http://www.hrsprings.com/products/trak/" onclick="window.open(this.href);return false;
http://www.hrsprings.com/application/se ... /1516/2013" onclick="window.open(this.href);return false;
20, 22, 25, 30 mm spacer/adapter (Camaro application)
H&R does make thinner spacers http://www.trakplus.com/" onclick="window.open(this.href);return false; - similar to those below (from Motorsport Tech), but not for the GM Zeta wheel hub ID/OD
custom spacers:
http://www.motorsport-tech.com/wheel_spacers.html" onclick="window.open(this.href);return false;
http://www.motorsport-tech.com/wheel_adapters.html" onclick="window.open(this.href);return false;
Bill Harper
inov8r@windstream.net
inov8r@windstream.net
- eagle-co94
- Posts: 306
- Joined: Fri Oct 04, 2013 4:47 pm
- Location: Bloomington, Indiana
Re: CTSV2 wheels?
Looks like I'll have to fit one of my fronts and one of my coupe rears to see how they fit.
-James . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . "Life without knowledge is death in disguise."
- eagle-co94
- Posts: 306
- Joined: Fri Oct 04, 2013 4:47 pm
- Location: Bloomington, Indiana
Re: CTSV2 wheels?
I ran H&R Trak+ spacers on my MINI Clubman S on the Autobahn at speeds up to 145mph and on the Nurburgring throwing it into curves. I always look to H&R first for wheel spacers.
-James . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . "Life without knowledge is death in disguise."
-
- Posts: 10
- Joined: Wed Mar 14, 2018 11:09 am
- Location: MN
Re: CTSV2 wheels?
I just picked a set of sedan wheels and the front tires rub on the pass side strut and the drivers side has maybe a 1/8 in... Anybody else had that issue? Seems like it has quite a bit more - camber on the passenger side front and rear. I thought it seems to stick better going left lol is this normal on these? My car has 25k now and is nice and tight yet and was really hoping these wheels would bolt right on
2011 9C3
2013 9C1
2013 9C1
Re: CTSV2 wheels?
use a 3mm spacer on the fronts
Re: CTSV2 wheels?
Would you need to run longer studs with 20mm spacers? I bought the car with 285's on CTSV's so I thought they fit until I noticed wear on the inner fender liner. Now I'm concerned.
Jim
Jim
Jim Chesnutt
1968 Camaro -my first car.
1995 Black/White 9C1 Caprice
2012 Alto Gray Metallic 9C1 Caprice--The HoDag-Solo axle back exhaust, improved racing OTR CAI intake.
2013 Black/White 9C1--NADACOP-DOD Delete with BTR Stage II cam, Kooks Headers, Solo Hi-flow Cats and Header Back Mach Balanced kit, WestBendDyno tuned.
1968 Camaro -my first car.
1995 Black/White 9C1 Caprice
2012 Alto Gray Metallic 9C1 Caprice--The HoDag-Solo axle back exhaust, improved racing OTR CAI intake.
2013 Black/White 9C1--NADACOP-DOD Delete with BTR Stage II cam, Kooks Headers, Solo Hi-flow Cats and Header Back Mach Balanced kit, WestBendDyno tuned.
-
- Posts: 2304
- Joined: Sat Feb 07, 2015 2:31 pm
- Location: Pearland, Texas
Re: CTSV2 wheels?
Unless it’s all the time, don’t be. We’ve ‘polished’ the inner fender wells of our 3rd Gen Firebird with Hoosier slicks every time we install a new set. They also rub on the LCAs a bit. Except for the time we ran new tires after the fresh mini-tub install, and discovered a bead of welding rod sitting proud , we’ve been fine.
Gene Beaird,
Pearland, Texas
2012 Caprice 9C1
1992 B4C 1LE Camaro
2018 Tahoe PPV (her car)
1995 DGGM Impala SS
1985 Firebird - 310 LS1 C Prepared autocross car.
1980 Bluebird Wanderlodge
And some others
Do YOU have my SPID?
Pearland, Texas
2012 Caprice 9C1
1992 B4C 1LE Camaro
2018 Tahoe PPV (her car)
1995 DGGM Impala SS
1985 Firebird - 310 LS1 C Prepared autocross car.
1980 Bluebird Wanderlodge
And some others
Do YOU have my SPID?